Search Results for: 8

Mini Rotor Control Plus MP02

/tmp/con-5cb270f4069bc/2794_Product.jpg


The Stab DiSEqC 1.2 Mini-Rotor Control MP02 is the perfect tool for a
reliable DiSEqC installation. New nine button version as pictured above
right.


The Mini-Positioner Rotor Control MP02 allows for storage and automatic
recall of 4 sat positions directly from a PC-Card or a DiSEqC 1.0 receiver.
Connected to the cable between motor and receiver and directly powered by the
receiver itself, it converts DiSEqC 1.0 codes into DiSEqC 1.2 codes to drive the
motor. Besides the buttons for the manual rotation eastwards and westwards, the
mini-positioner is provided with 4 push-buttons for memorisation of 4 sat
positions, 1 push-button for memorisation of the limits; 1 push-button to remove
the limits; 1 push-button for the “zero” function allowing the motor to re-align
to the zero position at any moment.


Easy to use, in 5 minutes it enables the dish to be perfectly pointed with
only the help of the field strength meter. The Rotor Control connected to the
cable between the motor and the receiver, is a DiSEqC1.2 command generator for
turning the motor east and west, fed directly from the receiver. The ‘zero’
function, which allows the motor to return perfectly aligned to zero at any
moment, is of particular importance when the Rotor Control is permanently
installed near the receiver and when the user is not very familiar with the OSD
of the receiver. Just by pressing the ‘zero’ button, besides the alignment to
zero, all functions previously memorized are reset, thus avoiding nearly all
calls for assistance.


Technical Specification:



  • Power Supply: 13/18Vcc

  • Consumption in Standby Mode: 5mA

  • Consumption in Operating Mode: 15mA

  • Attenuation: < 6dB

  • Operating Mode: Completely Transparent

  • Operating Protocol: DiSEqC 1.0

  • Generated Commands: DiSEqC 1.2

  • Programmable Positions: 4 Positions

  • Connection: F Connector

  • Dimensions: 32 x 74 x 30 mm

  • Weight: 120 grms

Satlook digital NIT

/tmp/con-5cb270f4069bc/2791_Product.jpg

The Satlook Digital is a Swedish made Sat-TV Instrument and
Spectrum-Analyzer. The unit is made for exact alignment and adjustment of
Satellite Dishes. It is intended for professional use when high accuracy and
precise information are needed.


 


It’s easily operated without a lot of unnecessary buttons and
knobs. The basic functions are easy to get a hold on and takes only minutes to
learn. This instrument is provided with a 4.5″ B/W-monitor which either shows
normal Sat-TV channel, the frequency spectrum 920-2150 MHz (or parts thereof)
alt. Digital data. Menus/help-displays are shown on the LCD-screen (64×128)
beside the monitor.

Analog Sat-TV channels can be tuned in and viewed
upon (Multistandard Video PAL, NTSC and SECAM). Audio frequencies between
5.5-8.5 MHz can be listened to. The Spectrum can be extended (zoom in) for
correct adjustment for the polarization (“cross-polarization”). The instrument
has very high resolution and accuracy. It presents measured data _+2 dB (at
around 20 C.)

SATLOOK Digital presents, under one of the sub menus.
digital information like BER (bit error rate), constellation diagram (QPSK) and
S/N (Signal/Noise Ratio). Satlook Digital can be handle a lot of
memory-positions and both spectrum-pictures and certain frequencies can be saved
(both analog and digital transponders).

The polarization of the LNB is
switchable 13V/18V and Hi-Lo Band with 22 KHz-tone. The DISEQC-function controls
all DISEQC-accessories (like switches, LNB’s and actuators). The power of the
instrument is supplies by a built in and rechargeable battery. Even though the
instrument has lot of functions it is still very light and
flexible.


Specifications:




  • Input Frequency:   920-2150MHz (easily reduced to
    250MHz max zoom in)



  • Frequency Display: L.O. can be setup. Yes, IF default. All
    standard LNB



  • Min. Level in:        
    About 35 dBuV (noise).



  • Max Level in:        
    About 90 dBuV.



  • Attenuation:         
    15 dB attenuator on/off.



  • Display of signal level: (analogue) dB on LCD/monitor.
    Pitch-tone.



  • Display of signal level: (Digital) S/N (signal/noise-ratio) BER
    (bit error rate) Constellation (QPSK)



  • TV/Audio standard: Multi TV/Audio (PAL, NTSC, SECAM).



  • KU- C-band: Yes, selectable.



  • Audio bandwidth :    Adjustable between 5.5 MHz
    and 8.5 MHz



  • Input impedance:    75 Ohm, BNC-con.



  • Picture-screen:       4.5″-monitor,
    B/W



  • Menus:                 
    On LCD 64×128.



  • Memory:               
    100 spectrum pictures can be stored with name. Stored spectrum can be mixed
    for easy identification of satellite.-“Max hold” function.



  • Favorite channels: Both analogue and digital frequencies can be
    stored (with name). Simultaneous measuring of up to 10 channels at the same
    time. Each channel with individual setup of 13/18v and 22 kHz on/off.



  • PC-connection: Yes, RS232-output



  • Power out: Yes, 13-18V



  • 22 kHz tone: Yes, on/off.



  • DiSEqC: Yes, all 1.0 and 1.1. Also Tone burst on/off.



  • DiSEqC actuator: Built in positioner for DiSEqC 1.2, SatScan and
    SatSelect.



  • Battery: Rechargeable 12V, 3.5 amp/hour.



  • Operational: About 1 hour on a fully charged battery.



  • Weight: About 5 kg (11 lbs)  including battery.



  • Accessories: Nylon carrying-case.



  • Power-supply: 100-240V/50/60Hz   13.5V,1.7
    Amp.



  • Car-charger.



  • BNC/F-adapter

Satlook Digital NIT Color

/tmp/con-5cb270f4069bc/2792_Product.jpg

The SATLOOK NIT COLOR is a swedish made SAT-TV instrument and
spectrum-analyzer.The unit is made for exact alignment and adjustment of
satellite-dishes. It is intended for professional use when high accuracy and
precise information are needed.


It´s easily operated without a lot of unnecessary buttons and knobs. The
basic functions are easy to get a hold on and takes only minutes to learn. The
instrument is provided with a 5″ 16:9 LCD-monitor which either shows “Free to
air” SAT-TV-channel (Digital or Analog), the frequency spectrum 920-2150 MHz (or
parts thereof) alt. Digital data. Menus/help-displays are shown on the LCDscreen
(64×128) beside the monitor.


“Free to air” Digital (DVB-S, QPSK) and Analog SAT-TV channels can be tuned
in and viewed upon (Multistandard Video PAL, NTSC and
SECAM).
Audiofrequencies between 5.5 – 8.5 MHz can be listened to.


The spectrum can be expanded (zoom in) for correct adjustment of the
polarisation (“cross-polarisation”).The instrument has very high resolution and
accuracy. It presents measured data ±2 dB (at around 20° C). SATLOOK NIT COLOR
presents, under one of the sub menus, digital information like BER (bit error
rate), constellationdiagram (QPSK) and S/N (signal/noise ratio).


SATLOOK NIT COLOR in the bitstream (NIT = Network Information Table). The NIT
also contains info about the transponders TV and Radio channels.


SATLOOK NIT COLOR can handle a lot of memory-positions and both
spectrum-pictures and certain frequencies can be saved (both analog and digital
transponders). The polarisation of the LNB is switchable 13V/18V and the Hi-Lo
band with 22 kHz-tone. The DiSEqC-function controls all DiSEqC-accessories (like
switches, LNB´s and actuators). The power of the instrument is supplied by a
built in and rechargeable Li-lon battery. Even though the instrument has a lot
of functions it is still very light and flexible.


Technical Specification:


Input frequency: 920-2150MHz, easily reduced to250 MHz (max zoom in).

Frequency display: Yes, IF default. All standard LNB L.O. can be
setup.
Min level in: About 35 dBμV (noise).
Max level in: About 90
dBμV.
Attenuation: 15 dB attenuator on/off.
Display of
signallevel:
(analog) dB on LCD-monitor. Pitch-tone.
Accuracy: ±2 dB (at
+20° C)
Display of signallevel: (Digtal) S/N (signal/noise-ratio) BER (bit
error rate) Constellation (QPSK)
Satellite-identification: Yes, by reading
out the NIT in the bitstream. Info about the TV and Radio channels.
TV/Audio
standard: Multi TV/Audio (PAL, NTSC, SECAM).
KU- C-band: Yes,
selectable.
Audio bandwidth : Adjustable between 5.5 and 8.5 MHz
Input
impedance: 75 Ohm, BNC-con.
Picture-screen: 5” 16:9 TFT-LCD monitor
Menus:
On LCD 64×128.
Memory: 100 spectrum pictures can be stored with name. Stored
spectrum can be mixed for easy identification of
satellite.-“Maxhold”-function.
PC-connection: Yes, RS232-output
Power out:
Yes, 13-18V.
22 kHz tone: Yes, on/off.
DiSEqC: Yes, all 1.0 and 1.1. Also
Toneburst on/off.
DiSEqC actuator: Built in positioner for DiSEqC 1.2,
SatScan and SatSelect.
Battery: Rechargable 12v, 3.5
amp/hour.
Operational: About 1 hour on a fully charged battery.
Weight:
About 3 kg incl.battery.

Satlook Mark IV FTA

/tmp/con-5cb270f4069bc/2793_Product.jpg

EMITOR SATLOOK Mark IV FTA is a measuringinstrument developed and
manufactured in Sweden for exact alignment and adjustment of
satellite-dishes.
The instrument is provided with a 4″ TFT-color monitor
which either shows Digital Free To Air, analog TV-channel or the frequency
spectrum 920-2150 MHz (normal or expanded mode).
Soundfrequencies between 5.5
8.5 MHz can be tuned in and listened to.
The polarisation of the LNB is
switchable with a 22 kHz tone and/or with 13V/18V. DiSEqC-accessories (like
switches) can also be controlled. Even DiSEqC-actuators (level 1.2) can be run
in the Digital FTA mode.
The instrument is protected from short-circuit when
connecting the LNB.
The main functions of the Digital Free To Air receiver
are controlled on the instrument´s key-pad but can also be fully controlled with
the attached remote-control. Power to the instrument is supplied by a built in,
rechargeable battery.
The battery is recharged from the external battery
charger or the car-adaptor.
Even though the instrument has a lot of functions
it is still very flexible and easy to use.
SATLOOK Mark IV FTA weights only
about 5,5kg incl. the battery and carrying-case.


 


Input frequency: 950-2150MHz.
Min level
in: About 30 dBuV (noise).
Max level in: About 100
dBuV.
TV/Audio standard: PAL.
Input
impedance: 75 Ohm, BNC-con.
Picture-screen: 4″
Color TFT monitor
KU- C-band: Yes,
selectable.
Audio bandwidth: Adjustable between 5.5 MHz and
8.5 MHz
Measuring method:


1. Full spectrum, normal or expanded mode.
2. 4” monitor with full
picture. Optional with pos/neg video.
3. Leavel check on single channel with
LED-bar display.
4. Level check with audio from loudspeaker.
5. FTA
Digital signal readout. Max leavel: Spectral with max peaks.


Two digits LED display with max value.
LED bar with max
indication.
Highest tone from loudspeaker.
FTA Digital max signal.


Supply voltage LNB: 13-18V, switchable
Tone
switch: 22 KHz. On / Off.
DiSEqC: Standard DiSEqC,
level 1.0.
Output: Video and Audio output for connection to
TV / monitor.
Operational: About 1 hour on a fully charged
battery.
Weight: Aprox. 5.5 kg
incl.battery.
Power supply: Internal rechargeable battery
12V 3.0 Amp. External power supply, In: 100-230V. Output 13.5V 1.5 amp DC.
Caradaptor.
Accessories: Nylon carrying-case.
Adaptor BNC
/ F-connector.
Remote control for FTA set-top box.

Maxpeak TAM DVB-T TERRESTRIAL METER

/tmp/con-5cb270ecb8c99/2788_Product.jpg


Maxpeak TAM-MV is a battery powered hand held DVB-T terrestrial alignment
meter. It is preprogrammed from the web via built in USB. With built in scanning
function. All difficult tasks like programming and difficult menu or operation
is eliminated. Extremely fast and accurate.


Specification:



  • Band III VHF and UHF

  • Replacable F-connector

  • 75 Ohm imp 30 to 100 dBuV

  • RF level as dBm or dBuV.

  • True MER or SNR displayed in dB

  • Pre and Post BER in numerical value

  • Quality displayed in % (reverse BER)

  • RF, BER,MER,CSI displayed together

  • Scan mode to how found channels

  • Backlite graphics display 128×64 dots

  • Integrated rechargable NiMH battery

  • Charged from wall adaptor or car

  • Up to 80 transmitters dividable in sub groups

  • Upgrade of settings via USB 2.0

  • Upgrade of firmware via USB 2.0

  • Language option via USB 2.0

  • Built in audible sounder

  • DVB-T active antenna support

  • Run time in excess of 4 hours

  • 200x75x56 mm 800 grams

Maxpeak SAM DVB-S SATELLITE METER

/tmp/con-5cb270ecb8c99/2789_Product.jpg

Maxpeak SAM is a battery powered hand held satellite alignment meter. It
powers the LNB and is preprogrammed from the web via built in USB. Unique touch
wheel to acess all functions. All difficult tasks like programming and difficult
menu or operation is eliminated. Extremely fast and accurate with high
sensetivity. Developed for DTH & the VSAT market. Low symbol rate e.g.
2000

Specification:



  • High sensitivity -75dBm

  • C, Ku, Ka or L band

  • Replacable F-connector

  • 75 Ohm imp 30 to 100 dBuV

  • RF level as dBm or dBuV.

  • True MER or SNR displayed in dB

  • Pre and Post BER in numerical value

  • Quality displayed in % (reverse BER)

  • RF, BER,MER displayed together

  • Backlite graphics display 128×64 dots

  • 32 bit processor

  • Integrated rechargable NiMH battery

  • Charged from wall adaptor or car

  • Meter operates whilst charging

  • Up to 70 sats

  • Upgrade of settings via USB 2.0

  • Upgrade of firmware via USB 2.0

  • Language option via USB 2.0

  • Built in audible sounder

  • DiSEqC switch commands and 22 K tone

  • Run time in excess of 4 hours

  • 200x75x56 mm, 800 grams

ALPHACRYPT CAM


The Alphacrypt CI Module is a seven in one CAM offering compatibility
with Irdeto 1+2, Viaccess 1+2, Betacrypt, Nagravision Alladin (Premiere), Conax,
Cryptoworks and Skycrypt.


Alphacrypt has its own integrated parental control system and can receive
software updates via the Astra satellite through the ORF transponder to the
latest version 3.11.


The Alphacrypt CAM is compatible with programme services like Arena, ORF,
Nova, MTV, Stream, Canal + NL, Pink Plus, Xtra Music, Kabelvision, Spice
Platinum, INXWORLD, FreeX-TV, AB Sat and many more.


Technical Specification:



  • Product Description: EuroCAM
  • Firmware / Software : 3.19
  • SAP No. : 901650
  • Standards : DVB, PCMCIA type II
  • Special Features : Supports terrestrial, satellite, cable reception
  • CAS compatible with Conax, CryptoWorks, Viaccess 1+2, Irdeto 1+2 ,
    Betacrypt ,Nagravision Alladin (Premiere)
  • Integrated parental control
  • Information regarding Software Upgrade via Satellite (only possible after
    Firmware Version 1.10): ORF-Transponder / ASTRA 19.2°Ost, 12.693 GHz H,
    Symbolrate 22.000, FEC 5/6. PID for manual search: 00546
  • Smart Card Interface: ISO7816

ALPHACRYPT LIGHT CAM


Not everyone needs all the features of a fully-fledged Alphacrypt module with
its multitude of integrated encryption systems. The Alphacrypt Light CI Module
is a 2 in 1 CAM offering compatibility with Betacrypt and Skycrypt and is the
perfect device for watching the German Premier services.


Alphacrypt has its own integrated parental control system and can receive
software updates via the Astra satellite through the ORF transponder.


Technical Specification:



  • Product Description: EuroCAM

  • SAP No. : 904410

  • Standards : DVB, PCMCIA type II

  • Special Features : Supports terrestrial, satellite, cable reception

  • CAS compatible with Betacrypt, Skycrypt

  • Integrated parental control

  • Information regarding Software Upgrade via Satellite (only possible after
    Firmware Version 1.10): ORF-Transponder / ASTRA 19.2°Ost, 12.693 GHz H,
    Symbolrate 22.000, FEC 5/6.

  • Smart Card Interface: ISO7816

Invacom Flansch Universal Quad QDF-031

/tmp/con-5cb27089d4e4e/2767_Product.jpg

**discontinued product** 

Universal Quad LNB 0.3dB C120

A high performance universal LNB with 4 independent switched outputs, for dishes supplied with their own feed-horn.
Typically used with fixed dishes to supply 4 receivers, in areas where the signal strength is poor.

Some customers find that the Invacom Quad LNBs outperform the single and twin LNB in low signal areas.

Input Frequency: 10.7 ~ 12.75 GHz
Output Frequency: 950 ~ 2150 MHz
Noise Figure: 0.3 dB typical
Gain: 50 ~ 60dB
Interface: C120 flange, 18.5 Ø
Ideal Dish F/D: N/A

 

Invacom Flansch Quad Polar QPF-031

/tmp/con-5cb27089d4e4e/2768_Product.jpg

Quad Polar LNB (CP LP)
A 4 fully switched output CP/LP LNB with
simultaneous reception of Linear & Circular polarisations

 

Input Frequency
FSS BandBSS
Band

 11.7 – 12.2 GHz
& 12.2-12.7GHz12.2 – 12.7 GHz
Output Frequency
FSS Band
BSS
Band
 950 – 1450 MHz
950 – 1450 MHz
Noise Figure
0.3dB typical
Gain
50 – 60dB
Interface
18.5 mm Diameter Waveguide,
C120 Flange
Ideal dish F/D
 N/A